flightview96

Fiat 500 Replacement Key Fob If your 500 remote key fob isn't functioning, it could be time to replace the battery. If you replace the battery and it doesn't work the issue could be somewhere else. United Locksmith specializes in the creation of new keys for classic vehicles. We have the tools as well as the parts needed for this service. Dead Coin Battery A dead battery is the main reason for your Fiat 500 keyfob not locking or unlocking the doors. The key fob contains a coin cell battery that is prone to draining quickly when it isn't frequented enough. If your remote started to show signs of weakness such as a loss of range and then completely stopped working it is likely that the battery is dead. Metal clips keep the battery securely in the key fob. If the clips aren't tight enough, it could lead to contact issues that will stop the remote from receiving power. With a small flathead screwdriver, push the clip that holds the retaining pin open to remove the battery, and replace it with a brand new one. Make sure you use a replacement battery with the same kind of voltage, the same size and specifications as the original battery. Water exposure can cause the key fob to corrode or be damaged. Even a brief bath in soapy water may harm the electronic chip within. It is best to keep your key fob in a dry location. replacement fiat 500 key fob could be the reason behind your key fob's inability to function properly. The rubber seals on key fobs keep them from getting damaged by a slight splash or drizzle of water. However, it's essential to keep the car keys away from the washing machine, the ocean, and pool. The key fob comes with an electronic chip inside that sends a signal car's immobilizer system. The chip allows the 500 to be locked and started. If it gets wet it will cease to function. If you're interested in checking if your key fob is still working, you can clean the internal electronics with isopropyl or electronic cleaner. However, it's better to purchase a new one from a dealer instead of trying to repair the key fob that is submerged in salt water. Although a replacement fob may cost you a little bit of money, it is far less expensive than having to pay for your Fiat 500 to be towed to the dealer and repaired! You can also make it yourself in just only a few steps. Be sure to have the correct battery type before you attempt to open your keyfob. You can find step-bystep directions for any key fob in your car online. Faulty Chip The chip in the key fob connects directly with the immobiliser of your car to ensure that your vehicle will only start once the proper keys are inserted. If the chip is damaged or damaged in any way the car won't start. A damaged chip could occur due to a variety of reasons, but most often it is due to water damage or the battery being dead. Whatever the reason, it's best to delegate the job to a locksmith since they will be able to replace the chip fast and at a reasonable cost. If your key fob will not function after being exposed to clean water from a tap or rain take the battery off. Wipe down the electronic component with an old towel. If the key fob still fails to work, it is likely to be a damaged chip that is required to be replaced. Some people will go to their dealer if they require an entirely new Fiat fob. But, this can be costly. United Locksmith is the best place to go if you would like to have your Fiat key fob replaced at a reasonable price. We have the tools and experience required to repair your Fiat key fob in a timely and professional way. Faulty Receiver Module Fiat key fobs send an electronic signal to the vehicle, which will unlock and close doors (and start the car if it has an automatic transmission) up to 50 feet. However there are a few factors that can cause the fob to stop working. It could be due to a dead battery damaged by water or worn buttons, a receiver module issue and signal interference or a malfunctioning electronic chip. If the fob was located in the pocket that has been subject to severe trauma (such as being dropped on the floor, or washed in the washer) the fob may not be in a position to connect with the Body Control Module (BCM) of the car. The BCM is a security device that can only accept signals from genuine keys. If this is the case, then you will need to replace your fob. A professional locksmith can take care of every aspect of the key replacement procedure, including programming a new one for your 500. They can even provide the fob cloned to work just like the original (and costs only less than what it would cost).